Search results

  1. dannyfiveforty

    ABC strut rebuild with new seals

    Can I ask, seems like the right thread. What nm should this bolt be after remanufacture? Thanks
  2. dannyfiveforty

    Possible turbo issue?

    What ultimately fixed these fault codes for you Abey? Thanks
  3. dannyfiveforty

    OM642 exhaust pressure sensor

    I have fault code 2616. Control variation pressure too high.
  4. dannyfiveforty

    OM642 exhaust pressure sensor

    Snoman, what was ultimately the outcome of this problem. I see it was several years ago now but my 150k om642 is having problems with this sensor and wondering about a underlying problem that could be the cause.. Many thanks
  5. dannyfiveforty

    Code P2616, bucking and loss of power

    Thanks, yes I am thinking of doing this before replacing whole turbo, matching turbo part number up with new solenoid and going from there. Thanks
  6. dannyfiveforty

    Code P2616, bucking and loss of power

    Ok thanks, problem I have got is it will do it once every 500 miles or so
  7. dannyfiveforty

    Code P2616, bucking and loss of power

    Did anyone get to the bottom of this problem? I have read numerous solutions such as changing turbo, changing actuator only, boost leaks.. etc I get this bucking on full power sometimes also, throws no eml or codes apart from 2616-2 Thanks
  8. dannyfiveforty

    Rumbling and light knocking from ABC

    Ok thanks, I have investigated again today, if I select drive I get a light knocking (2 or 3 times) which resonates through the rear pulsation dampener. Then if I select reverse I get the same again..
  9. dannyfiveforty

    Rumbling and light knocking from ABC

    Good morning all, I have recently changed the rear struts on my 2008 CL63. Car has now gone through its mot and height sits fine and goes up and down no problem, I can get it to go up and down when the car is stationary absolutely perfect with no noises. when going along there is a rumbling...
  10. dannyfiveforty

    where to get headbolts done?

    Good afternoon all, I am considering who to get to do the headbolts on my 2008 CL. I have briefly spoken to MSL who have suggested to leave alone until I get symptoms. However, I think I would be happier to get them done, preferably the 'One at a time' route as to not disturb too much down...
  11. dannyfiveforty

    Help with Aircon problem please

    I have a mobile aircon guy coming out to it next week. Cheers guys
  12. dannyfiveforty

    Help with Aircon problem please

    Its pressure testing good, and holding. but I don’t know what weight is in there.
  13. dannyfiveforty

    Help with Aircon problem please

    ah ok, I think I follow, there’s no direct relationship between pressure and the weight in there? It could be that pressure is reading high (30psi) but there’s not enough in? Obviously if this is the case I need to get an aircon specialist to look at it now as like you say it would be guess work.
  14. dannyfiveforty

    Help with Aircon problem please

    good evening all, I have a problem with my Aircon and don’t know what route to go next. Car (2008 CL63) had ‘aircon off’ permanently lit and fault code of low refridgerant pressure. I have increased the pressure by adding gas using stp refill kit. Pressure is up to 30psi (on the low...
  15. dannyfiveforty

    Setting the date and time - W221 / C216

    Done, thanks
  16. dannyfiveforty

    Setting the date and time - W221 / C216

    That’s great thankyou, where can I go to to download the file I need? Thanks
  17. dannyfiveforty

    Setting the date and time - W221 / C216

    good morning all, I have a cl63 and am having a problem setting date and time. I have seen it is a problem on preface lift W221 also. I have done a search and found various methods such as parking under a car park, (didn’t work for) and turning command off the night before and going into...
  18. dannyfiveforty

    Auto boot open/close fault

    good morning, My recently acquired 2008 CL63 has a button on the inside of the bootlid to close it. It dosnt illuminate and dosnt do anything when pressed. I’ve checked all related fuses and are all fine. I have read about a fluid level to check? Any other advise? Things I can do before main...
  19. dannyfiveforty

    Slight shake at idle

    Yes to confirm it’s the M156 motor in a 2008 216CL. Thanks for the ideas so far guys
  20. dannyfiveforty

    Slight shake at idle

    evening all, My cl63 has got a very slight, but noticeable inconsistent shake at idle but only when up to temperature. The car is new to me and I am changing oil and plugs at the weekend but have read that this can be common on the M156? And something to check is the inlet manifold gasket...


As a member of ourMercedes Owners' club, you will enjoy numerous savings on an expanding range of services including, Insurance, Parts and Servicing, RAC Membership plus much more.MBOmembers can save around £200.00 a year. You can join from as little as £30.00 and start to enjoy these savings immediately. You receive our monthly magazine and free classified ads when you decide to trade up a model.
Top Bottom