Help cl600 is Kaput

[Stuartph600]

Today’s work

Throttle body wiring checked for continuity

Did another make shift ecu reset and throttle body adaption and got car running and up to temp

1st video is car running

2nd video is throttle body make shift adaption with engine at 80c engine is off but you hear throttle body working

 

[alexanderfoti]

That throttle body doesn't sound too healthy.

How was the wiring?

 

[Stuartph600]

That throttle body doesn't sound too healthy.

How was the wiring?

A bit of corrosion on pins to ecu

Ive got another engine loom on its way from germany

 

[Stuartph600]

This arrived in the post today

Only painful part in fitting looks like getting access to the knock sensors

 

[alexanderfoti]

This arrived in the post today

Only painful part in fitting looks like getting access to the knock sensors

Yes they need the turbos to come off I believe.

 

[Stuartph600]

Yes they need the turbos to come off I believe.

I hope not , think that would be end of the car for me

 

[alexanderfoti]

Just cut the loom where the connectors go into the knock sensor wire and solder/heatshrink.

 

[Stuartph600]

Just cut the loom where the connectors go into the knock sensor wire and solder/heatshrink.

Won’t know sensors be shielded wiring

 

[alexanderfoti]

Won’t know sensors be shielded wiring

No just 2 wires.

 

[LostKiwi]

For purposes of testing you won't need knock sensors.
If the car runs with the new loom then you know the problem was that and can then look into reconnecting the wiring. If not there's no point.

 

[Stuartph600]

So.......

At the moment car is starting up ok and not misfiring or bad throttle body issue

But

Getting fault code P2003 secondary air injection fault

Possible I've upset the vacuum line to it or relay issue ?

ABS light on but only getting fault code C1540 and C1540-008 component B24/15 Rotary speed and lateral sensor

Is it a possible drive to adapt to get ABS light to go out?

But guess could be wheel speed sensor which my icarsoft won't deal with

New loom not fitted yet......

 

[LostKiwi]

ABS may reset after the car gets to about 8km/h as it recalibrates itself.

 

[alexanderfoti]

So.......

At the moment car is starting up ok and not misfiring or bad throttle body issue

But

Getting fault code P2003 secondary air injection fault

Possible I've upset the vacuum line to it or relay issue ?

ABS light on but only getting fault code C1540 and C1540-008 component B24/15 Rotary speed and lateral sensor

Is it a possible drive to adapt to get ABS light to go out?

But guess could be wheel speed sensor which my icarsoft won't deal with

New loom not fitted yet......

Check the actuation valves at the front of the engine, they have the Vac lines going to them from the changeover valve on the back left valve cover. (not the divert air one just below it). Its easy to break the brittle plastic barbs off them..... Secondary air can be coded out if its a pain.

 

[Stuartph600]

ABS may reset after the car gets to about 8km/h as it recalibrates itself.

Ah that sounds good , a little drive next week once the snows gone me thinks

 

[Stuartph600]

Check the actuation valves at the front of the engine, they have the Vac lines going to them from the changeover valve on the back left valve cover. (not the divert air one just below it). Its easy to break the brittle plastic barbs off them..... Secondary air can be coded out if its a pain.

I did plugs and valve cover that side so guess i must of upset something

 

[Stuartph600]

Todays Work

Checked vac lines for secondary air , replaced some and make good fitting on vac pump

Took car for a 10 minute drive , ABS light did not go out

Checked codes after drive secondary air fault still present but no light on dash

Re started car and then....... intermittent spikes of revs without touching throttle pedal

Then ESP fault and misfiring again

P202E C1041 P2042

Plug code reader in i notice my moisture trap behind passenger seat had gone over dumping sticky fluid all under passenger seat

Fluid mopped up but notice it has gone down air vent and under carpet all way to front of the seat

Whats under the seat that could be affected

Codes cleared and i fitted one of my spare throttle pedals

Ran ok for 5 mins

 

[alexanderfoti]

Do you have any of those codes from a MB star machine?
What is giving you those codes?

Nothing under either seat that would give running problems, seat controllers etc live under there.

What is this water leak you have?

 

[Stuartph600]

Just Closing this thread down now

Towel thrown in

Thank you to everyone who helped

Stuart

 

[alexanderfoti]

Just Closing this thread down now

Towel thrown in

Thank you to everyone who helped

Stuart

Sorry to hear Stuart, have you taken the car to a garage? Be good to hear of the outcome.

 

[Stuartph600]

Sorry to hear Stuart, have you taken the car to a garage? Be good to hear of the outcome.

No its not been to a garage , even if it was fixed it would still be going , urgent need for a running car with 4 doors and 4x4 now

Thanks for you're help