C207 2012 Brake Pipe Repair

MrGundam

Active Member
Joined
Feb 15, 2021
Messages
40
Reaction score
15
Your Mercedes
C207 2012 E350Cdi
Evening all,

So after owning this car only 1 week one of the brake lines bursts!

Seems there was a load of crud on top of the plastic under carriage right up against the brake lines.

qbwYQzj.jpg


Which has resulted in one of the lines bursting and the one next to it corroded.

x4IBv6z.jpg


I have inspected the rest of the lines and it is actually in good condition apart from the section that burst and was up against the moist dirt.

yyxVhg9.jpg

heS5Gva.jpg


Now I know the best 'sure fire' thing would be to have all the pipes replaced, but given the rest is in good condition I am thinking about repairing the straight section with the corrosion. I will call a local indy I was recommended on Monday but given I would need a tow and then the cost of the work I would expect a bill for around £500 - £600.

I actually called a another local Mercedes Independent that was open and when asked for a quote on replacing all the lines they said they would recommend replacing the corroded part only as per MB. I keep reading people online however saying the whole lines need replacing.

So I just wondered if my thinking is ok / safe:
1) Use a quality DIN handheld flare tool (Vigor V4416) so I create a bubble flare on the existing pipe at a completely clean part.
2) Use about a meter of 3/16" copper brake pipe with males nuts and joiners
3) Coat the joins and pipe with wax seal
4) Bleed the system with a pressure bleeding kit (Sealey VS820)
5) Possibly use my iCarsoft V2 to purge any air from ABS? (Not sure how much leaked out before saw the warning message)
6) Test / check / Test / Check
 

ajlsl600

Senior Member
Joined
Nov 18, 2013
Messages
9,031
Reaction score
6,029
Location
france
Your Mercedes
clk3202001,sl6002003 with everything regrettably sold ,A class 170cdi auto. NG/TF1800 ML250
If done correctly and cut back to good no issue with repair.pipes like much else made of rubbish designed NOT to last .good old bundy lasted yrs.
 
OP
M

MrGundam

Active Member
Joined
Feb 15, 2021
Messages
40
Reaction score
15
Your Mercedes
C207 2012 E350Cdi
  • Thread Starter
  • Thread starter
  • #3
If done correctly and cut back to good no issue with repair.pipes like much else made of rubbish designed NOT to last .good old bundy lasted yrs.
What's 'bundy'? I assume a short copper section is OK assuming it will not rub and is secured properly so no stress?
 

Mr Greedy

Senior Member
Joined
Feb 15, 2012
Messages
551
Reaction score
573
Location
Leicestershire
Your Mercedes
E350/2011/OM642 265bhp
Depending on access, ask a good independent if it's worthwhile replacing more of that straight run, where it's very simple to do and basically doesn't change the job, so that maybe you can get the joints somewhere protected (like high up behind wheel arch liners), and it also means that it will only be the CuNi pipe exposed to the worst of the weather/wet road. I'm not saying pay hardly any more, but if a longer section can be put it virtually at the same cost, I'd be enquiring about that.
 

mattkh

Senior Member
Joined
Aug 2, 2006
Messages
3,157
Reaction score
353
Location
England
Your Mercedes
A160 W168 1999 1.6
Remove the bit you decided to replace and use it as a template to bend the copper pipe.
 

ajlsl600

Senior Member
Joined
Nov 18, 2013
Messages
9,031
Reaction score
6,029
Location
france
Your Mercedes
clk3202001,sl6002003 with everything regrettably sold ,A class 170cdi auto. NG/TF1800 ML250
As above. You can get a cheap flarin tool that will get to where u need it. My proper flaring tool wil not get into tight spaces the copper stuff flares real easy.
 

onefortheroad

Senior Member
Joined
Dec 8, 2015
Messages
3,409
Reaction score
2,026
Location
uk.
Your Mercedes
Me -2019 GLC 350 coupe AMG line. Mrs- ford kuga 65 plate awd powershift .
Is that the rear most undertray you removed ?
 
OP
M

MrGundam

Active Member
Joined
Feb 15, 2021
Messages
40
Reaction score
15
Your Mercedes
C207 2012 E350Cdi
  • Thread Starter
  • Thread starter
  • #9
Is that the rear most undertray you removed ?
The corrosion / much was the NS undertray in the middle of the car. Seems a load of mud / stones somehow got in there and sat against the brake lines. The rest of the lines are absolutely fine so I have gone the repair route.
 

sonic

Senior Member
Joined
Nov 21, 2009
Messages
3,578
Reaction score
2,382
Location
Staffordshire
Your Mercedes
E350CDI, SLC250d, FJR 1300
I have always intend to take my undertrays & give the underside a clean out.
Is it much of a job to get them back on again?
 
OP
M

MrGundam

Active Member
Joined
Feb 15, 2021
Messages
40
Reaction score
15
Your Mercedes
C207 2012 E350Cdi
  • Thread Starter
  • Thread starter
  • #11
I have always intend to take my undertrays & give the underside a clean out.
Is it much of a job to get them back on again?
I'll let you know end of weekend :)

Removing them isn't too bad. I was shocked at how much dirt was stuck in there sat against the brake lines! 1 week I have had this and already had a ruptured brake line. These are not checked in an MOT as it is covered. Scary.
 

Wighty

Senior Member
Joined
Aug 4, 2016
Messages
13,434
Reaction score
12,465
Location
Sunny Essex
Your Mercedes
W211/E320cdi/2009 and CLK200k 2009
I'll let you know end of weekend :)

Removing them isn't too bad. I was shocked at how much dirt was stuck in there sat against the brake lines! 1 week I have had this and already had a ruptured brake line. These are not checked in an MOT as it is covered. Scary.
If you just bought the car , you must be covered by the sellers warranty ??
 


Comand (Europe) Ltd are the leading specialists in supplying and fitting Comand, Linguatronic, Media interface kits, UHI phone, IPod interfaces and much more.
Top Bottom