W124 differential

Martin-Jundiaí

Senior Member
Joined
Jan 5, 2005
Messages
50
Reaction score
0
Has anyone had to rebuild a w124 300E diff? Is it as tricky as the manual suggests?

Recently my car has started with a rumble whilst slowing down and I feel the bearings are worn, the car has done around 80K miles. However, further investigation proved hat the diff was almost dry! How that has happen I can only imagine the previous owner(s) were not so careful about maintainance. I bought the car 16K miles ago and was assured the oils had been changed!

Thanks, Martin
 
Last edited:

television

Always remembered RIP
Joined
Mar 14, 2005
Messages
164,073
Reaction score
367
Age
89
Location
Daventry
Your Mercedes
2002 SL500, 216 CL500, all fully loaded
It depends on you engineering skills, MB axles do not have pinion bearing section that comes off, the crown wheel and pinion need to be blued to check that the mesh is central on the tooth faces.

There a few firms that still do it for around £250-£300
 

Number_Cruncher

Senior Member
Joined
Oct 10, 2007
Messages
1,806
Reaction score
3
Your Mercedes
1995 W124 E300D TE
>>Is it as tricky as the manual suggests?

Yes, it's incredibly easy to end up with a noisy whining expensive diff. Unless you have a very unusual and coveted rear axle ratio, I would investigate obtaining a second hand unit.

In terms of expense, the crown wheel and pinion gear pair are over £400. By the time you've added the bearings, seals, shims, collapsible spacer, and gaskets, you'll have quite a parts bill.

You'll need to be able to measure the pinion drag torque, and the crown wheel to pinion backlash, and some experience in interpreting gear contact patterns in engineer's blue is also helpful.

I'm quite experienced and bold, and wouldn't hesitate for long before stripping an MB engine or gearbox, but, I wouldn't be able to guarantee to be able to rebuild a diff for a luxury car and be sure that it would be sufficiently quiet.
 

230K

Senior Member
Joined
Aug 22, 2004
Messages
499
Reaction score
1
Age
54
Location
Belfast
Your Mercedes
E300TD/1998/3.0 Diesel
Hi

My advice would be spend £10 and put 1.1L of Millers fully synthetic diff oil in it and see how the noise is then. You could be surprised!!

230K
 

turbopete

Senior Member
Joined
Feb 4, 2009
Messages
14,209
Reaction score
331
Age
48
Location
Spennymoor
Your Mercedes
2017 '17' Ford Mondeo 2.0TDCi ST Line X 180 (sorry)
seconded here. even try refilling and adding molyslip to the oil. it can help! as number cruncher already stated, unless you can get access to the right equipment, materials and have the confidence and knowledge to do such a job, under no circumstances would i recommend that you try to re-build the unit yourself!! id be reluctant to tackle it, and i worked as a mechanic for 14years!
 
OP
Martin-Jundiaí

Martin-Jundiaí

Senior Member
Joined
Jan 5, 2005
Messages
50
Reaction score
0
  • Thread Starter
  • Thread starter
  • #6
Thanks for the replies and the comments have been well noted!

In Brazil, there are some things which cost a fortune and one is a 'specialised' MB garage at R$150 an hour! Imagine paying 150 quid an hour! Indie MB garages tend to be a touch shady...to say the least. There are rumours about one in particular that 'finds' things wrong with the car...even when you didn't ask them to check it out and when YOU knew it was working perfectly!

Well, I'm going to look around for a second-hand unit and until then I'll flush out the diff and fill it with a slightly heavier oil (SAE 90?)and see if I can find Molyslip or the such-like.
 
Last edited:
OP
Martin-Jundiaí

Martin-Jundiaí

Senior Member
Joined
Jan 5, 2005
Messages
50
Reaction score
0
  • Thread Starter
  • Thread starter
  • #8
I've been chatting to a MB technician on the Brazilian MB forum and he claims that if it's just the bearings that are worn, it shouldn't be too complicated to swap them out. Luckily where I live most of the major bearing manufacturers have retail outlets so good quality parts are readily available. I may investigate this route too.

The line drawings available from that Russian EPC should at least give the mechanic an idea BEFORE removing the diff.
 
OP
Martin-Jundiaí

Martin-Jundiaí

Senior Member
Joined
Jan 5, 2005
Messages
50
Reaction score
0
  • Thread Starter
  • Thread starter
  • #9
After discussing this topic with the mechanic yesterday. He asked me if I could get a hold of torque specs and tolerances. It appears that the noise is coming from the from bearing, which he claims is not such a difficult job to do.

So the question is...does anyone have these settings? I'm trying to find them on other forums too.

Thanks once again, Martin
 
Last edited:


AMF Automotive - We are an independent Mercedes-Benz and AMG specialist located in Paddock Wood, Kent, with full Mercedes Diagnostic equipment. We offer a full portfolio of tuning options for AMGs and can cater for all your Mercedes needs.
Tel: 0203 384 4644www.amfmercedes.com/
Top Bottom